Straight answers on sizes, thickness, weight, grades, MTC, pricing and ordering — so your enquiry is specification-ready before you send it.
01
What is a W beam?
W Beams refers to wide-flange sections whose broad flanges distinguish them from narrow-flange profiles. It is used in wide-flange structural frames, industrial buildings, bridges and heavy engineered supports. The name identifies a profile family, not a safe load rating; final selection must follow the approved drawing, BOQ, project standard and responsible engineer’s calculations.
02
Why are W beams called wide-flange beams?
W beams are commonly described as wide-flange sections because their flange width is substantial relative to many narrow-flange I profiles. This is a geometry description, not a load approval. The exact W designation, section properties, grade and design calculations must control procurement.
03
Which W beam dimensions and weights are listed?
The live page shows 75 x 40 mm to 400 x 100 mm, with 3 mm to 25 mm thickness; the chart lists 7.126 kg/m to 50.300 kg/m. These are catalogue values rather than confirmation of ready stock. Quote the exact section designation, dimensional standard, material grade, length and quantity, and verify the selected row against the approved project documents.
04
How is a W beam different from an NPB or IPE beam?
W Beams has its own dimensional and mass series. A similar nominal depth in another family can have different flange width, thickness, radii, mass and section properties. Compare recognised section tables and approved calculations; never treat related profile names as automatic equivalents.
05
Why must the exact W section designation be stated?
No substitution or structural selection should be made from profile name, span, flange width or unit weight alone. Capacity depends on loads, combinations, span, orientation, lateral restraint, buckling, deflection, connections, fire requirements and the design code. Any change from W Beams requires revised calculations and written approval.
06
How are W beam weight per foot and weight per metre compared?
Use one consistent unit system when comparing quotations or calculating tonnage. Convert only from the published value for the exact designation and dimensional standard; do not mix figures from different tables. Ask the supplier to confirm kg/m as the commercial weight basis if the project BOQ uses metric units.
07
Can a W beam be selected because its flange is wider?
No substitution or structural selection should be made from profile name, span, flange width or unit weight alone. Capacity depends on loads, combinations, span, orientation, lateral restraint, buckling, deflection, connections, fire requirements and the design code. Any change from W Beams requires revised calculations and written approval.
08
Does a heavier W beam automatically carry the required project load?
No substitution or structural selection should be made from profile name, span, flange width or unit weight alone. Capacity depends on loads, combinations, span, orientation, lateral restraint, buckling, deflection, connections, fire requirements and the design code. Any change from W Beams requires revised calculations and written approval.
09
What is the current commercial rate for W Beams per kg?
Do not publish a fixed current W Beams price per kg. The rate changes with steel grade, section mass, quantity, length, finish, market date and supply route. Send the exact designation, standard, total tonnage and delivery postcode for a dated quotation, then confirm GST, freight and fabrication inclusions.
10
Can W Beams be purchased on a per-tonne basis?
A current W Beams price per tonne can be quoted for a defined requirement. State the exact section, material grade and standard, length, pieces or tonnage, finish, MTC, inspection and destination. Compare offers on the same weight basis and verify tax, freight, cutting, packing and documentation terms.
11
What affects the delivered price of W Beams?
The landed cost of W Beams depends on grade, section availability, unit mass, order mix, total tonnage, length, cutting, drilling, coating, testing, inspection, packing and transport. An uncommon designation or mixed small quantities may price differently from one repetitive bulk section.
12
What MOQ applies when buying W Beams?
The live page states a minimum order quantity of 1 tonne. Confirm how MOQ applies when the enquiry mixes sections, grades, special lengths, finishes or inspection requirements. Provide the piece count and calculated tonnage for every line item so commercial feasibility can be reviewed accurately.
13
Should buyers assume every W Beams designation is in stock?
Do not assume every W Beams designation, grade and length is ready stock. Availability should be confirmed against the exact specification, quantity and enquiry date. If timing matters, state the required date and ask whether the quotation is based on stock, incoming material or a reviewed supply requirement.
14
Is an MTC available for a W Beams order?
Request the MTC for W Beams at the enquiry stage, stating certificate type, grade standard, heat traceability and project format. Check that the certificate matches the supplied markings, dimensions and product form. A generic document does not establish compliance with every structural, toughness or coating requirement.
15
Which documents should accompany W Beams inspection?
Inspection for W Beams should cover identification, dimensions, web and flange thickness, length, straightness, surface condition, quantity, marking and MTC traceability. For third-party inspection, specify the agency, stage, hold points, acceptance criteria and required reports before ordering.
16
Can W Beams be supplied to approved cutting and drilling drawings?
Cutting, drilling or fabrication of W Beams can be reviewed against an approved drawing. Provide cut lengths, hole centres, copes, notches, end plates, weld details, tolerances and piece marks. Connection design, welding procedures and any structural modification remain subject to engineer and fabricator approval.
17
Can a specified surface finish or coating be requested for W Beams?
The live page lists hot-rolled, galvanised or customer-specified for W Beams. State the required surface condition, coating or galvanising standard, preparation, appearance and inspection. Coating suitability depends on the base material, fabrication sequence and exposure, and galvanised steel is corrosion-resistant rather than permanently rust-proof.
18
Which applications use W Beams?
W Beams are considered for wide-flange structural frames, industrial buildings, bridges and heavy engineered supports. Suitability depends on the exact section properties, material grade, exposure, span, restraints, loads, connections and fire requirements. Final use must follow approved calculations, drawings, BOQ and applicable project standards.
19
Where can I buy W Beams in Mumbai or nearby states?
Ferrite can review W Beams requirements for Mumbai, Navi Mumbai, Maharashtra, nearby states, India-wide supply and export enquiries. Availability and logistics depend on section and quantity. Provide the delivery postcode or destination port, Incoterm, unloading constraints and required date for review.
20
What should an India or export W Beams enquiry include?
For a fast W Beams quotation, send the profile and exact designation, dimensions, material grade, material and dimensional standards, length, pieces, tonnage, finish, make preference, MTC and inspection requirements. Add fabrication drawings, delivery postcode or port, Incoterm and required date where applicable.
